Get Special Discount Offer of 1Y0-241 Certification Exam Sample Questions and Answers
New 1Y0-241 Dumps For Preparing CCA-AppDS Certified Citrix Exam Well
NEW QUESTION # 54
Scenario: The Citrix Administrator of a Linux environment needs to load balance the web servers. Due to budget constraints, the administrator is NOT able to implement a full-scale solution.
What can the administrator purchase and install to load balance the webservers?
- A. Citrix ADC VPX
- B. Citrix ADC SDX
- C. Citrix ADC MPX
- D. Citrix ADC CPX
Answer: D
Explanation:
it is the CPX, which is not a full scale solution. You don't need a full virtual like VPX to run CPX inside Docker for Linux, that is the budget choice.
NEW QUESTION # 55
Which Citrix ADC monitor can a Citrix Administrator use to check the authentication service of the Active Directory (AD) domain controller?
- A. A ping monitor with the IP address of the AD domain controller in the special parameters
- B. An LDAP monitor with the LDAP Script Name, Configured Base DN, Bind DN, Filter, Attribute and Password parameters in the basic parameters.
- C. A TCP monitor with the LDAP Base DN configured in the basic parameters.
- D. A MYSQL-ECV monitor with the Base DN, Bind DN, Filter, Attribute, and Password parameters configured in the basic parameters
Answer: B
Explanation:
https://docs.citrix.com/en-us/citrix-adc/current-release/load-balancing/load-balancing-builtin-monitors/monitor-ldap-services.html
NEW QUESTION # 56
Scenario: In general, it is recommended to do the following:
Use _________ if you want the Citrix ADC to reset or drop a connection based on a client or request-based parameter.
Use _________ to redirect traffic or respond with custom messages.
Use _________ for manipulating data on HTTP requests and responses.
- A. rewrite, rewrite, responder
- B. responder, redirect, rewrite
- C. responder, responder, rewrite
- D. rewrite, responder, rewrite
Answer: C
NEW QUESTION # 57
What
is the effect of the "set cs vServer-CS-1 -redirectURL http://www.newdomain.com/mysite/" command?
- A. All the requests without URL path/mysite/ will be redirected to http://www.newdomain.com/mysite/.
- B. If the vServer-CS-1 encounters a high connection rate, then users will be redirected to http://www.newdomain.com/mysite/.
- C. All the requests to vServer-CS-1 will be redirected to http://www.newdomain.com/mysite/.
- D. If the status of vServer-CS-1 is DOWN, then users will be redirected to http://www.newdomain.com/mysite/.
Answer: D
Explanation:
Explanation
https://support.citrix.com/article/CTX108946/how-to-configure-redirect-url-on-adc-virtual-server-when-virtual-s
NEW QUESTION # 58
Which Citrix ADC platform offers an out-of-the-box multi-tenant solution?
- A. SDX
- B. VPX
- C. MPX
- D. CPX
Answer: A
NEW QUESTION # 59
Scenario: A Citrix Administrator configured the rewrite policies below:
bind lb vServer VIP1_http -policyName POL_14 -priority 120 -gotoPriorityExpression END -type REQUEST bind lb vServer VIP1_http -policyName POL_12 -priority 90 -gotoPriorityExpression NEXT -type REQUEST bind lb vServer VIP1_http -policyName POL_15 -priority 100 -gotoPriorityExpression END -type REQUEST bind lb vServer VIP1_http -policyName POL_13 -priority 101 -gotoPriorityExpression NEXT -type REQUEST Which policy will be evaluated last considering POL_12 is hit first?
- A. POL_15
- B. POL_14
- C. POL_12
- D. POL_13
Answer: B
Explanation:
Explanation
answer: C. POL_14
Short Explanation with reference:
The Citrix ADC appliance evaluates the rewrite policies in the order of their priority, from lowest to highest.
The priority is a numerical value that indicates the relative importance of the policy. The lower the priority, the higher the importance. The gotoPriorityExpression is an expression that specifies the next policy to evaluate after the current policy is hit. The expression can be either a priority value or the keyword END, which indicates that no further policies are evaluated. Therefore, in this scenario, the policy evaluation order is as follows:
POL_12 is hit first, as it has the lowest priority (90). It has a gotoPriorityExpression of NEXT, which means that the next policy in priority order is evaluated.
POL_15 is evaluated next, as it has the next lowest priority (100). It has a gotoPriorityExpression of END, which means that no further policies are evaluated.
POL_13 and POL_14 are not evaluated, as they have higher priorities (101 and 120) than POL_15, and POL_15 has a gotoPriorityExpression of END.
Therefore, the correct answer is C. POL_14, as it is the policy that is evaluated last, considering POL_12 is hit first.
Configuring rewrite policies | NetScaler : Policy binding and evaluation | NetScaler 14.1
NEW QUESTION # 60
Scenario: A Junior Citrix Administrator needs to create a content switching vServer on a Citrix ADC high availability (HA) pair. The NSIP addresses are 192.168.20.10 and 192.168.20.11. The junior administrator connects to NSIP address 192.168.20.10 and saves the changes.
The following day, a Senior Citrix Administrator tests the new content switching vServer, but it is NOT working. The senior administrator connects to the HA pair and discovers that everything the junior administrator configured is NOT visible.
Why has the Citrix ADC lost the newly added configurations?
- A. The Citrix ADC appliances have different firmware versions.
- B. Both Citrix ADCs in the HA pair restarted overnight.
- C. The junior administrator connected to the NSIP of the secondary Citrix ADC in the HA pair.
- D. The junior administrator made the changes and did NOT force a failover to save the configuration.
Answer: C
Explanation:
Explanation
"You are connected to the secondary node..." when first login to the NSIP and after saving the configuration
NEW QUESTION # 61
Scenario: A company has three departments with proprietary applications that need to be load balanced on a Citrix ADC. The three department managers would like to use the same IP address to access their individual applications. This would mean configuring three load-balanced vServers, all using the same IP address.
What can the Citrix Administrator configure for this scenario?
- A. Three different admin partitions that allow use of the same IP address for each load-balanced vServer on a Citrix ADC
- B. Three SNIPs with the same IP address on a Citrix ADC
- C. Three different Citrix ADCs that use the same IP address
- D. Three different load-balanced vServers with three different IP addresses on a Citrix ADC
Answer: B
NEW QUESTION # 62
Scenario: A Citrix Administrator needs to create local, limited-privilege user accounts for other administrators. The other administrators will require only:
Read-only access
The ability to enable and disable services and servers
Which built-in command policy permission level can the administrator use?
- A. Operator
- B. Read-only
- C. Sysadmin
- D. Network
Answer: B
NEW QUESTION # 63
A Citrix Administrator deploys a new Citrix ADC MPX appliance in the demilitarized zone (DMZ), with one interface in the DMZ and the other on the internal network.
In which mode should the administrator deploy the Citrix ADC?
- A. Transparent
- B. One-arm
- C. Two-arm
- D. Forward proxy
Answer: C
Explanation:
Explanation
answer: B. Two-arm
Short Explanation with reference:
A two-arm deployment is a common scenario where the Citrix ADC appliance has two network interfaces, one connected to the DMZ network and the other connected to the internal network1. This allows the appliance to act as a gateway between the two networks and provide load balancing, security, and optimization features for the applications hosted on the internal servers2. A two-arm deployment also provides better isolation and protection for the internal network than a one-arm deployment, where the appliance has only one network interface connected to a switch or router that spans both networks3. A transparent mode is a packet forwarding mode that enables the appliance to act as a Layer 2 device and bridge packets that are not destined for it4. A forward proxy mode is a feature that enables the appliance to act as an intermediary between clients and servers on the internet, caching web content and applying policies. Neither of these modes are relevant for the scenario described in the question.
1: Citrix ADC at a Glance 2: Tech Paper: Best practices for NetScaler ADC Deployments 3: Configure a Citrix ADC BLX appliance with a network mode 4: Packet forwarding modes | NetScaler 14.1 : Configuring Forward Proxy | NetScaler 14.1
NEW QUESTION # 64
A Citrix Administrator wants to configure independent and isolated access on a single appliance to allow three different departments to manage and isolate their own applications.
What can the administrator configure to isolate department-level administration?
- A. Dedicated routes in the admin partitions for each department
- B. Admin partitions that use dedicated VLANs
- C. A SNIP in each partition, and bind a VLAN for the department
- D. Policy-based routes for each department in the nsroot partition
Answer: B
Explanation:
Explanation
answer: A. Admin partitions that use dedicated VLANs
Short Explanation with reference: Admin partitions are a feature of Citrix ADC that allow administrators to create multiple logical partitions on a single physical appliance. Each partition is independent and isolated from the others, and has its own configuration, resources, and management. This enables administrators to delegate administration tasks to different departments or customers, while maintaining security and operational consistency1. Admin partitions can use dedicated VLANs to isolate the network traffic of each partition from the others2. A SNIP in each partition, and bind a VLAN for the department (option B) is also a valid way to isolate network traffic, but it does not provide configuration and management isolation. Policy-based routes for each department in the nsroot partition (option C) and dedicated routes in the admin partitions for each department (option D) are not relevant for isolating department-level administration, as they are used for routing traffic based on policies or routes3. Therefore, the correct answer is A. Admin partitions that use dedicated VLANs.
NEW QUESTION # 65
Scenario: A Citrix Administrator is configuring a Citrix ADC high availability (HA) pair with an existing primary Citrix ADC with all resources configured. The administrator adds the secondary Citrix ADC in HA and discovers that the configuration on the existing primary was removed and is now the secondary Citrix ADC in the HA pair.
Which two configurations could the administrator have used to prevent this from happening? (Choose two.)
- A. Enable HA monitoring on all primary device interfaces.
- B. Enable HA monitoring on all secondary device interfaces.
- C. Set the primary Citrix ADC to stay primary in the Configure HA Node settings.
- D. Set the secondary Citrix ADC to stay secondary in the Configure HA Node settings.
Answer: B,D
Explanation:
Forcing the node to stay secondary works on both standalone and secondary nodes. On a standalone node, you must use this option before you can add a node to create an HA pair. When you add the new node, the existing node stops processing traffic and becomes the secondary node. The new node becomes the primary node.
https://docs.citrix.com/en-us/citrix-adc/current-release/system/high-availability-introduction/forcing-a-secondary-node-to-stay-secondary.html On a standalone node, you must use this option before you can add a node to create an HA pair. When you add the new node, the existing node continues to function as the primary node, and the new node becomes the secondary node.
https://docs.citrix.com/en-us/citrix-adc/current-release/system/high-availability-introduction/forcing-the-primary-node-stay-primary.html
NEW QUESTION # 66
Scenario: To receive data alerts for failures, a Citrix Administrator is configuring SNMP on the Citrix ADC.
The administrator is confident that the manager, alarms and SNMP traps are configured correctly. The following week, there is a Citrix ADC-related outage and the administrator does NOT receive any alerts.
What could be the reason for this alert failure?
- A. The Citrix ADC is configured for SNMP version 1.
- B. The community name was NOT configured in the Citrix ADC SNMP trap destination settings.
- C. The Citrix ADC only has standard licensing.
- D. The Citrix Web App Firewall is blocking the alerts from going out.
Answer: B
NEW QUESTION # 67
Scenario: A Citrix Administrator configured a Citrix ADC active-passive, high availability (HA) pair. The HA pair failed over and customers were unable to access hosted websites. The administrator troubleshoots and discovers that the upstream router is NOT updating its ARP table.
What can the administrator configure to resolve this issue?
- A. Independent Network Configuration (INC) mode
- B. Route monitor
- C. HA monitor
- D. Virtual MAC
Answer: D
Explanation:
Explanation
answer: D. Virtual MAC
Short Explanation with reference:
Virtual MAC (VMAC) is a feature that allows the Citrix ADC appliance to use a common MAC address for both the primary and secondary units in a high availability (HA) pair1. This prevents the upstream router from having to update its ARP table when a failover occurs, as the MAC address of the active unit remains unchanged2. VMAC can be enabled or disabled by using the -vmac option in the CLI or by checking or unchecking the Enable VMAC check-box in the GUI1. Therefore, the correct answer is D. Virtual MAC.
1: Configuring VMACs | NetScaler 2: How to Set Up a High Availability Pair on ADC - Citrix Customer Support
NEW QUESTION # 68
Scenario: A Citrix Administrator is concerned about the number of health checks the Citrix ADC is sending to backend resources. The administrator wants to find a way to remove health checks from specific bound services.
How can the administrator accomplish this?
- A. Use the no-monitor option.
- B. Use reverse-condition monitoring.
- C. Unbind the current monitor.
- D. Use service groups to minimize health checks.
Answer: A
NEW QUESTION # 69
A Citrix Administrator configured an external syslog server but is NOT seeing detailed TCP information?
What could be causing this?
- A. Log facility is NOT configured.
- B. TCP logging is NOT enabled.
- C. User-defined audit log is NOT configured.
- D. Log level is NOT enabled.
Answer: B
Explanation:
Explanation
https://support.citrix.com/article/CTX226058
NEW QUESTION # 70
Scenario: A Citrix Administrator needs to integrate LDAP for Citrix ADC system administration using current active directory (AD) groups. The administrator created the group on the Citrix ADC, exactly matching the group name in LDAP.
What can the administrator bind to specify the permission level and complete the LDAP configuration?
- A. A nested group to the new group
- B. An authentication, authorization, and auditing (AAA) action to the group
- C. A command policy to the group
- D. Users to the group on the Citrix ADC
Answer: C
NEW QUESTION # 71
Scenario: A Citrix ADC receives packets destined for a MAC address owned by the Citrix ADC. The destination IP address of the packets does NOT belong to the Citrix ADC. Layer 3 mode is enabled by default on the Citrix ADC.
The Citrix ADC will __________ the packets in this scenario. (Choose the correct option to complete the sentence.)
- A. drop
- B. bridge
- C. route
- D. process
Answer: C
NEW QUESTION # 72
......
Updated 1Y0-241 Dumps Questions Are Available For Passing Citrix Exam: https://www.surepassexams.com/1Y0-241-exam-bootcamp.html
Free UPDATED Citrix 1Y0-241 Certification Exam Dumps is Online: https://drive.google.com/open?id=1rvdLXyOUcyvFfBPLVQetHx9VZZStdPlF