Updated Free NACE NACE-CIP2-001 Test Engine Questions with 100 Q&As
The Best CIP Level 2 NACE-CIP2-001 Professional Exam Questions
NEW QUESTION 24
Inspectors perform tests on linings that they may not perform on exterior coatings because
- A. linings protect the contents and the container.
- B. coatings are more durable than linings.
- C. linings are more durable than coatings.
- D. coatings are expected to degrade over time.
Answer: A
NEW QUESTION 25
You should bulk store coatings containing isocyanates
- A. in a well ventilated area separate from the work place.
- B. in a heated warehouse.
- C. in a refrigerated warehouses
- D. wherever it is convenient
Answer: A
NEW QUESTION 26
Inspector reports should always be copied to:
- A. The Owner only
- B. The Contractor and Owner
- C. Whomever the Owner identifies
- D. All parties involved in the project
Answer: C
NEW QUESTION 27
Ideally, documentation requirements should be defined:
- A. By the contractor
- B. In the specification
- C. At the pre-job conference
- D. By the inspector
Answer: B
NEW QUESTION 28
As a NACE Level 2 Inspector on a field job; prior to submission your documentation should always reviewed and approved by:
- A. A NACE Level 1 Inspector
- B. A NACE Protective Coating Specialist
- C. Another NACE Level 2 Inspector
- D. A NACE Level 3 Inspector
Answer: D
NEW QUESTION 29
Linings are used on the interior of pipelines to
- A. provide protection against soil chemicals.
- B. protect the transported product.
- C. reduce magnetic polarity.
- D. afford limited temperature insulation.
Answer: B
NEW QUESTION 30
Pre-cleaning of work pieces will NOT remove
- A. mill scale.
- B. oil or grease.
- C. dirt.
- D. snow, ice or water.
Answer: A
NEW QUESTION 31
You are a NACE Level 2 in-house inspector working in a shop. Your in-house requires you to perform a sleeve test to test for soluble salts; however the 3 rd party NACE Level 3 inspector, the owner, has a san smart meter and has achieved a very different result and has rejected the pre-cleaning.
Your FIRST course of action is to:
- A. Redo the pre-cleaning based on the other inspectors results
- B. Advise your QC Manager to change the ITP to the use of the salt smart meter
- C. Review the specification with the other inspector to see what method was specified
- D. Advise the other inspector he is using an incorrect method
Answer: C
NEW QUESTION 32
When performing testing in accordance with ASTM D 2583 the inspector may observe:
- A. Adhesion failure
- B. Cold flow or creep
- C. Glue failure
- D. Cohesion failure
Answer: B
NEW QUESTION 33
The coating applicator has ignored a enface preparation hold point and applied coating over the surface without a sign off from you as the inspector.
Your FIRST preferred course of action is to:
- A. Advise the Owner and write a Non-Conformance report
- B. Ignore the situation
- C. Require the Applicator to remove the coating
- D. Stop the job
Answer: C
NEW QUESTION 34
When completing the Final Inspection report the Inspector should write the report using:
- A. Language that only in the project would understand
- B. Language that another NACE Inspector would understand
- C. Language that only technical experts would understand
- D. Language that the most would understand
Answer: D
NEW QUESTION 35
You are working as the only in-house NACE Level 2 Inspector in a shop setting when an independent 3 rd party NACE Level 3 Inspector, representing the owner, presents you with a copy of a Non Conformance Report (NCR) he has written for a NACE2/SSPC SP 10 centrifugal blast which you had previously approved.
Your FIRST preferred course of action is to:
- A. Review the NCR with the other Inspector
- B. Consult your supervisor
- C. Request a re-blast of the item in question
- D. Verbally challenge the NCR
Answer: B
NEW QUESTION 36
You are the NACE Level 2 Inspector with the final responsibility to prepare the final report for a very large structural steel shop project which has gone very well. It is due next week. The work has been ongoing for two years and several NACE Level 1 Inspectors have worked under your supervision throughout the project. You find you are missing one week of daily reports for the night shift from the very beginning of the project and despite your best efforts they are cannot found.
You FIRST preferred course of action is to:
- A. Do not complete your report until they can be found
- B. Re-create the reports as not much was going on during night shift anyway
- C. Use creative writing to cover over the fact they are missing
- D. Plainly state in your report that they are missing
Answer: D
NEW QUESTION 37
In the event of a conflict between the Product Data Sheet and the Specification:
- A. It is up to the Applicator to decide which one to follow
- B. The Specification prevails
- C. It is up to the Inspector to decide which one to follow
- D. The Product Data Sheet prevails
Answer: B
NEW QUESTION 38
When a coating is expected to be exposed to temperatures above 93C (200 F) the best choice would be:
- A. Latex
- B. Polyurea
- C. Inorganic Coatings
- D. Organic coatings
Answer: C
NEW QUESTION 39
Because a NACE Level 2 Inspector has been trained in specific destructive tests, it is up to the Inspector to decide if and when a destructive test is required.
- A. True
- B. False
Answer: B
NEW QUESTION 40
In powder coatings, when the particles of powder begin to flow but are not fully liquid, they are in what stage?
- A. Wetting stage
- B. Flow stage
- C. Gel stage
- D. Cure stage
Answer: B
NEW QUESTION 41
Inspection and Test Plans are provided to:
- A. To supersede the requirements of the product data sheets
- B. So the Inspector doesn't have to read the entire specification
- C. So the contractor has a single document to reference
- D. Outline the inspection steps, sequencing and pass/fail criteria
Answer: D
NEW QUESTION 42
......
Try 100% Updated NACE-CIP2-001 Exam Questions [2023]: https://www.surepassexams.com/NACE-CIP2-001-exam-bootcamp.html
Pass NACE-CIP2-001 Exam - Real Questions and Answers: https://drive.google.com/open?id=1JsjtdJTt2WgrWB3_hovKgCG0jO7jdGr_